vos_shadow - Creates a shadow copy of a volume on a different server/partition
vos shadow [-id] <volume name or ID on source> [-fromserver] <machine name on source> [-frompartition] <partition name on source> [-toserver] <machine name on destination> [-topartition] <partition name on destination> [-toname <volume name on destination>] [-toid <volume ID on destination>] [-offline] [-readonly] [-live] [-incremental] [-cell <cell name>] [-noauth] [-localauth] [-verbose] [-encrypt] [-noresolve] [-help]
vos sh [-id] <volume name or ID on source> [-froms] <machine name on source> [-fromp] <partition name on source> [-tos] <machine name on destination> [-top] <partition name on destination> [-ton <volume name on destination>] [-toi <volume ID on destination>] [-o] [-r] [-l] [-in] [-c <cell name>] [-noa] [-lo] [-v] [-e] [-nor] [-h]
The vos shadow command creates a shadow copy of a volume on a different partition or server.
A shadow volume is a copy of a volume that does not normally appear in the volume location database (VLDB). It is a primitive operation that is meant to be used in backup or disaster recovery situations.
This command is not used during normal OpenAFS administration and may have adverse effects on the VLDB if not used properly! This command should only be used by an expert.
Using this command on a volume when the source volume is not the same as parent volume used to create the shadow will leave the destination volume in a unknown state.
Running vos syncserv or vos syncvldb on a fileserver containing shadow volumes will not update the VLDB with the shadowed Read/Write volumes as long as the entries for the source volumes still exist. In a disaster recovery situation the VLDB entries for the corresponding source volumes need hence to be deleted first.
Currently, the maximum quota for a volume is 2 terabytes (2^41 bytes). Note that this only affects the volume's quota; a volume may grow much larger if the volume quota is disabled. However, volumes over 2 terabytes in size may be impractical to move, and may have their size incorrectly reported by some tools, such as fs_listquota(1).
Specifies either the complete name or volume ID number of a read/write volume.
Identifies the file server machine where the source volume resides. Provide the machine's IP address or its host name (either fully qualified or using an unambiguous abbreviation). For details, see vos(1).
Names the partition where the source volume resides. Provide the full partition name (for, example, /vicepa) or one of the abbreviated forms described in vos(1).
Identifies the file server machine to which to copy the volume. Provide the machine's IP address or its host name (either fully qualified or using an unambiguous abbreviation). For details, see vos(1).
Names the partition to which to copy the volume. Provide the full partition name (for, example, /vicepa) or one of the abbreviated forms described in vos(1).
The complete name of the new volume to create.
Leaves the new volume flagged as off-line in the volume database.
Flags the new volume as read-only in the volume database.
Copies the live volume without cloning. This is normally not necessary and causes the volume to be kept locked for longer than the normal copy mechanism.
Copy the changes from the source volume to a previously created shadow volume.
Names the cell in which to run the command. Do not combine this argument with the -localauth flag. For more details, see vos(1).
Assigns the unprivileged identity
anonymous to the issuer.
Do not combine this flag with the -localauth flag.
For more details,
Constructs a server ticket using a key from the local /usr/afs/etc/KeyFile file. The vos command interpreter presents it to the Volume Server and Volume Location Server during mutual authentication. Do not combine this flag with the -cell argument or -noauth flag. For more details, see vos(1).
Produces on the standard output stream a detailed trace of the command's execution. If this argument is omitted, only warnings and error messages appear.
Encrypts the command so that the operation's results are not transmitted across the network in clear text. This option is available in OpenAFS versions 1.4.11 or later and 1.5.60 or later.
Shows all servers as IP addresses instead of the DNS name. This is very useful when the server address is registered as 127.0.0.1 or when dealing with multi-homed servers. This option is available in OpenAFS versions 1.4.8 or later and 1.5.35 or later.
Prints the online help for this command. All other valid options are ignored.
This command has no output unless
-verbose is specified or there is an error.
The issuer must be listed in the /usr/afs/etc/UserList file on the machines specified with the -toserver and -fromserver arguments and on each database server machine.
If the -localauth flag is included,
the issuer must instead be logged on to a server machine as the local superuser
vos(1), vos_backup(1), vos_copy(1), vos_move(1)
http://www.openafs.org/pipermail/openafs-info/2005-July/018469.html discusses motivation for the creation of this command.
http://workshop.openafs.org/afsbpw06/talks/drh.scs.html discusses one possible use for it.
Copyright 2008 Jason Edgecombe <email@example.com>
This documentation is covered by the BSD License as written in the doc/LICENSE file. This man page was written by Jason Edgecombe for OpenAFS.